Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We've encountered this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the internet and decided it made sense to share it with you on this page.
Setting up a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately hard task. If the old tub is easily easily accessible, the project can relocate speedily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will require a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified yourself for the work as well as are comfortable attempting it. Instead of hiring a professional to take control of a halfway-completed job, it is better to consider employing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your restroom if you have actually already acquired a brand-new tub and also do not need to alter the setup of your previous water pipes.
Your devices and also material list must consist of the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome due to the restricted gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washers remain in place between the faucet as well as the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the required placement. The wood boards are helpful in equally spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bathtub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water supply and also check all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill the tub as well as additionally examine the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bath tub ought to wait up until the bathtub has been utilized at least when as this will settle it right into its final position.
Planning for the Installment
First of all, the sustaining framework provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you use all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, causing the water to penetrate the wall between the bathroom and the tiling, causing problems with wetness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components as well as installations. They are sold in tubes and also cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the motion experienced when the tub is in usage. The sealant can crack rather very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that editorial about Installing A Bathtub through a good friend on another web address. Are you aware of anybody else who is excited by the niche? Feel free to promote it. Many thanks for going through it.
Search-end for emergency plumbing. Report this page